#
# ISC License
#
# Copyright (c) 2021, Autonomous Vehicle Systems Lab, University of Colorado at Boulder
#
# Permission to use, copy, modify, and/or distribute this software for any
# purpose with or without fee is hereby granted, provided that the above
# copyright notice and this permission notice appear in all copies.
#
# THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
# WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
# MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
# ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
# WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
# ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
# OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
#
r"""
.. raw:: html
<iframe width="560" height="315" src="https://www.youtube.com/embed/Fux_UsZ5FR0" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>
Overview
--------
Demonstrates how to use :ref:`spiceInterface` to load a Spice kernel with the Hubble orbital
information and use the corresponding :ref:`transRefMsgPayload` output message
to specify the spacecraft motion. With this approach the spacecraft attitude is still
dynamic and can achieve the same inertial pointing goal as setup in
:ref:`scenarioAttitudeFeedback`.
The script is found in the folder ``basilisk/examples`` and executed by using::
python3 scenarioSpiceSpacecraft.py
The simulation layout is
shown in the following illustration. Note that here the ``spiceInterface`` module
must be executed prior to :ref:`spacecraft` as the
:ref:`transRefMsgPayload` input message must be properly setup before initializing
the spacecraft module which reads this in during ``Reset()``.
.. image:: /_images/static/test_scenarioSpiceSpacecraft.svg
:align: center
When the simulation completes 2 plots are shown for the MRP attitude tracking error history,
as well as the Hubble inertial orbital coordinates with respect to the Earth.
Illustration of Simulation Results
----------------------------------
::
show_plots = True
.. image:: /_images/Scenarios/scenarioSpiceSpacecraft1.svg
:align: center
.. image:: /_images/Scenarios/scenarioSpiceSpacecraft2.svg
:align: center
"""
#
# Basilisk Scenario Script and Integrated Test
#
# Purpose: Integrated test of the spacecraft(), extForceTorque, simpleNav() and
# mrpFeedback() modules. Illustrates a 6-DOV spacecraft detumbling in orbit
# Author: Hanspeter Schaub
# Creation Date: Nov. 19, 2016
#
import os
import numpy as np
np.set_printoptions(precision=16)
# import general simulation support files
from Basilisk.utilities import SimulationBaseClass
from Basilisk.utilities import unitTestSupport # general support file with common unit test functions
import matplotlib.pyplot as plt
from Basilisk.utilities import macros
# import simulation related support
from Basilisk.simulation import spacecraft
from Basilisk.simulation import extForceTorque
from Basilisk.utilities import simIncludeGravBody
from Basilisk.simulation import simpleNav
# import FSW Algorithm related support
from Basilisk.fswAlgorithms import mrpFeedback
from Basilisk.fswAlgorithms import inertial3D
from Basilisk.fswAlgorithms import attTrackingError
# import message declarations
from Basilisk.architecture import messaging
# attempt to import vizard
from Basilisk.utilities import vizSupport
# The path to the location of Basilisk
# Used to get the location of supporting data.
from Basilisk import __path__
bskPath = __path__[0]
fileName = os.path.basename(os.path.splitext(__file__)[0])
[docs]def run(show_plots):
"""
The scenarios can be run with the followings setups parameters:
Args:
show_plots (bool): Determines if the script should display plots
"""
# Create simulation variable names
simTaskName = "simTask"
simProcessName = "simProcess"
# Create a sim module as an empty container
scSim = SimulationBaseClass.SimBaseClass()
# set the simulation time variable used later on
simulationTime = macros.min2nano(10.)
#
# create the simulation process
#
dynProcess = scSim.CreateNewProcess(simProcessName)
# create the dynamics task and specify the integration update time
simulationTimeStep = macros.sec2nano(.1)
dynProcess.addTask(scSim.CreateNewTask(simTaskName, simulationTimeStep))
#
# setup the simulation tasks/objects
#
# initialize spacecraft object and set properties
scObject = spacecraft.Spacecraft()
scObject.ModelTag = "Hubble"
# define the simulation inertia
I = [900., 0., 0.,
0., 800., 0.,
0., 0., 600.]
scObject.hub.mHub = 750.0 # kg - spacecraft mass
scObject.hub.IHubPntBc_B = unitTestSupport.np2EigenMatrix3d(I)
# add spacecraft object to the simulation process
# clear prior gravitational body and SPICE setup definitions
gravFactory = simIncludeGravBody.gravBodyFactory()
# setup Earth Gravity Body
earth = gravFactory.createEarth()
earth.isCentralBody = True # ensure this is the central gravitational body
mu = earth.mu
# attach gravity model to spacecraft
gravFactory.addBodiesTo(scObject)
# setup spice library for Earth ephemeris and Hubble states
timeInitString = "2015 February 10, 00:00:00.0 TDB"
spiceObject = gravFactory.createSpiceInterface(time=timeInitString, epochInMsg=True)
spiceObject.zeroBase = 'Earth'
scNames = ["HUBBLE SPACE TELESCOPE"]
spiceObject.addSpacecraftNames(messaging.StringVector(scNames))
spiceObject.loadSpiceKernel("hst_edited.bsp", bskPath + '/supportData/EphemerisData/')
# need spice to run before spacecraft module as it provides the spacecraft translational states
scSim.AddModelToTask(simTaskName, spiceObject)
scSim.AddModelToTask(simTaskName, scObject)
# setup extForceTorque module
# the control torque is read in through the messaging system
extFTObject = extForceTorque.ExtForceTorque()
extFTObject.ModelTag = "externalDisturbance"
scObject.addDynamicEffector(extFTObject)
scSim.AddModelToTask(simTaskName, extFTObject)
# add the simple Navigation sensor module. This sets the SC attitude, rate, position
# velocity navigation message
sNavObject = simpleNav.SimpleNav()
sNavObject.ModelTag = "SimpleNavigation"
scSim.AddModelToTask(simTaskName, sNavObject)
#
# setup the FSW algorithm tasks
#
# setup inertial3D guidance module
inertial3DObj = inertial3D.inertial3D()
inertial3DObj.ModelTag = "inertial3D"
scSim.AddModelToTask(simTaskName, inertial3DObj)
inertial3DObj.sigma_R0N = [0., 0., 0.] # set the desired inertial orientation
# setup the attitude tracking error evaluation module
attError = attTrackingError.attTrackingError()
attError.ModelTag = "attErrorInertial3D"
scSim.AddModelToTask(simTaskName, attError)
# setup the MRP Feedback control module
mrpControl = mrpFeedback.mrpFeedback()
mrpControl.ModelTag = "mrpFeedback"
scSim.AddModelToTask(simTaskName, mrpControl)
mrpControl.K = 3.5
mrpControl.Ki = -1 # make value negative to turn off integral feedback
mrpControl.P = 30.0
mrpControl.integralLimit = 2. / mrpControl.Ki * 0.1
#
# create simulation messages
#
# The MRP Feedback algorithm requires the vehicle configuration structure. This defines various spacecraft
# related states such as the inertia tensor and the position vector between the primary Body-fixed frame
# B origin and the center of mass (defaulted to zero). The message payload is created through
configData = messaging.VehicleConfigMsgPayload()
configData.ISCPntB_B = I
configDataMsg = messaging.VehicleConfigMsg().write(configData)
#
# connect the messages to the modules
#
sNavObject.scStateInMsg.subscribeTo(scObject.scStateOutMsg)
attError.attNavInMsg.subscribeTo(sNavObject.attOutMsg)
attError.attRefInMsg.subscribeTo(inertial3DObj.attRefOutMsg)
mrpControl.guidInMsg.subscribeTo(attError.attGuidOutMsg)
mrpControl.vehConfigInMsg.subscribeTo(configDataMsg)
extFTObject.cmdTorqueInMsg.subscribeTo(mrpControl.cmdTorqueOutMsg)
scObject.transRefInMsg.subscribeTo(spiceObject.transRefStateOutMsgs[0])
#
# Setup data logging before the simulation is initialized
#
numDataPoints = 100
samplingTime = unitTestSupport.samplingTime(simulationTime, simulationTimeStep, numDataPoints)
snLog = sNavObject.scStateInMsg.recorder(samplingTime)
attErrorLog = attError.attGuidOutMsg.recorder(samplingTime)
mrpLog = mrpControl.cmdTorqueOutMsg.recorder(samplingTime)
scSim.AddModelToTask(simTaskName, snLog)
scSim.AddModelToTask(simTaskName, attErrorLog)
scSim.AddModelToTask(simTaskName, mrpLog)
#
# set initial Spacecraft States
#
scObject.hub.sigma_BNInit = [[0.1], [0.2], [-0.3]] # sigma_BN_B
scObject.hub.omega_BN_BInit = [[0.001], [-0.01], [0.03]] # rad/s - omega_BN_B
# if this scenario is to interface with the BSK Viz, uncomment the following line
vizSupport.enableUnityVisualization(scSim, simTaskName, scObject
# , saveFile=fileName
)
#
# initialize Simulation
#
scSim.InitializeSimulation()
#
# configure a simulation stop time and execute the simulation run
#
scSim.ConfigureStopTime(simulationTime)
scSim.ExecuteSimulation()
# unload custom Spice kernel
gravFactory.unloadSpiceKernels()
spiceObject.unloadSpiceKernel("hst_edited.bsp", bskPath + '/supportData/EphemerisData/')
#
# plot the results
#
timeAxis = attErrorLog.times()
plt.close("all") # clears out plots from earlier test runs
plt.figure(1)
for idx in range(3):
plt.plot(timeAxis * macros.NANO2MIN, attErrorLog.sigma_BR[:, idx],
color=unitTestSupport.getLineColor(idx, 3),
label=r'$\sigma_' + str(idx) + '$')
plt.legend(loc='lower right')
plt.xlabel('Time [min]')
plt.ylabel(r'Attitude Error $\sigma_{B/R}$')
figureList = {}
pltName = fileName + "1"
figureList[pltName] = plt.figure(1)
plt.figure(2)
for idx in range(3):
plt.plot(timeAxis * macros.NANO2MIN, mrpLog.torqueRequestBody[:, idx],
color=unitTestSupport.getLineColor(idx, 3),
label='$L_{r,' + str(idx) + '}$')
plt.legend(loc='lower right')
plt.xlabel('Time [min]')
plt.ylabel(r'Control Torque $L_r$ [Nm]')
pltName = fileName + "2"
plt.figure(3)
for idx in range(3):
plt.plot(timeAxis * macros.NANO2MIN, attErrorLog.omega_BR_B[:, idx],
color=unitTestSupport.getLineColor(idx, 3),
label=r'$\omega_{BR,' + str(idx) + '}$')
plt.legend(loc='lower right')
plt.xlabel('Time [min]')
plt.ylabel('Rate Tracking Error [rad/s] ')
plt.figure(4)
for idx in range(3):
plt.plot(timeAxis * macros.NANO2MIN, snLog.r_BN_N[:, idx] / 1000.,
color=unitTestSupport.getLineColor(idx, 3),
label='$r_{BN,' + str(idx) + '}$')
plt.legend(loc='lower right')
plt.xlabel('Time [min]')
plt.ylabel('Inertial Position [km]')
figureList[pltName] = plt.figure(4)
if show_plots:
plt.show()
# close the plots being saved off to avoid over-writing old and new figures
plt.close("all")
return figureList
#
# This statement below ensures that the unit test scrip can be run as a
# stand-along python script
#
if __name__ == "__main__":
run(
True # show_plots
)